Silver Zinc Aerosol 400G 3in1 - PROTECT / MATCH / SEAL - Silver Zinc Supplies A101

ALL IN 1 EASY STEP

DESCRIPTION

• Product Code: A101
• Fluid Type: Zinc Aerosol
• Colour: Silver
• Packaging: 400g

Description
Silver Zinc is a fast drying epoxy based metallic zinc coating which provides excellent adhesion, corrosion resistance and long lasting durability to metal surfaces. It can be used as an anti-corrosive primer and top coat in a onestep application. It can also be used as a touch up coating for welded areas on galvanised products however for longer term protection and highly corrosive conditions Grey Zinc is recommended before the application of Silver Zinc as a finish coat.

FEATURES

• Fast drying
• Metallic Silver Finish
• Excellent Adhesion
• Corrosion Resistant
• Long lasting durability
• Protect-Match-Seal
• Industrial strength

APPLICATIONS
It can be used as an anti-corrosive primer and top coat in a onestep application. It can also be used as a touch up coating for welded areas on galvanised products however for longer term protection and highly corrosive conditions Grey Zinc is recommended before the application of Silver Zinc as a finish coat.

Suitable Surfaces: Steel, wrought iron, galvanised iron and non-ferrous metals such as; aluminium, alloys, ZINCALUME® and stainless steel with appropriate primer.

TYPICAL PROPERTIES OF SILVER ZINC
(Note:Data is typical and does not constitute a specification.)
Physical State    Liquid
Colour    Silver
Finish    Metallic
Odor    Solvent odour
Solubility in water    Not miscible with Water
Size    400g Aerosol
Propellant    Dimethyl Ether
Flash Point (°C)    -41 (propellant)
Flammability    HIGHLY FLAMMABLE.

INSTRUCTIONS

SUITABLE SURFACE
Steel, wrought iron, galvanised iron and non-ferrous metals such as; aluminium, alloys, ZINCALUME® and stainless steel with appropriate primer.

IDEAL APPLICATION TEMPERATURE
Between 10°C and 40°C. Avoid use in windy conditions.

PREPARATION
Surface should be clean, dry and free from contaminants such as rust, oil, grease, dirt and salt. Welds should be ground back to clean white metal. Thoroughly sand new metal and lightly sand previously painted surfaces to ensure maximum adhesion. Remove loose rust and flaking paint with a wire brush, scraper or mechanical sander. For best results, always remove rust back to bare metal. For superior protection and adhesion on mild steel surfaces and welds it is recommended to prime with Grey Zinc and allowing it to dry for 4-6 hours before applying 2 coats of Silver Zinc. For non-ferrous metals such as aluminium, alloys, ZINCALUME® and stainless steel use Grey Zinc.

APPLICATION
Surface should be clean, dry and free from contaminants such as rust, oil, grease, dirt and salt. Welds should be ground back to clean white metal. Thoroughly sand new metal and lightly sand previously painted surfaces to ensure maximum adhesion. Remove loose rust and flaking paint with a wire brush, scraper or mechanical sander. For best results, always remove rust back to bare metal. For superior protection and adhesion on mild steel surfaces and welds it is recommended to prime with Grey Zinc and allowing it to dry for 4-6 hours before applying 2 coats of Silver Zinc. For non-ferrous metals such as aluminium, alloys, ZINCALUME® and stainless steel use Grey Zinc.

COVERAGE
Approximately 2m2 per can (depending on the surface and amount of overspray).

DRYING TIME
Touch dry in 20 minutes (25°C). recoat after 1 hour. Hard dry in 16-24 hours. Drying will be slower in cold and humid conditions, in the absence of ventilation or where heavy film build is applied.

AFTER SPRAYING
Prevent blocking by holding the can upside down and spraying until only clear gas escapes. Also wipe pray tip of nozzle clean. Clean up wet paint with mineral turpentine, xylene or general purpose thinner.

STORAGE
Store locked up. Protect from sunlight. Do not expose to temperatures exceeding 50°C/122°F. Store in well-ventilated place.

DISPOSAL
Dispose of contents/container according to regional regulations.

Part Number/SKU: A101

* Product Images are for illustration purposes only, unless otherwise specified colour may be different.